Blackmagic videohub control software4/26/2023 ![]() NOTE: This information is on the Videohub Smart Control Pro Technical Specifications sheet in the documentation tab.Compact 1 rack unit size, approximately three inches deep.Buttons are illuminated by RGB for highest illumination quality.Button caps can be removed for easy labeling.Includes Mac and Windows software for control panel programming.Supports optional "take" button set via software configuration.Single or multiple destinations supported.110-250V volt AC powered for use with non powered ethernet.Ethernet connection with Power over Ethernet and non powered loop through.When used in dark rooms, all buttons can be backlit, so button labels can be clearly seen. All buttons are illuminated by RGB LEDs so that a wider range of rich and clean colors can be displayed. The button caps can be removed to allow labeling of buttons. If used in mission critical environments, Videohub Smart Control Pro could be connected to a dedicated switch and can be powered via power over ethernet (PoE) without the need for a power supply.ĭesigned to fit into creative post production facilities, it includes attractive crystal look buttons that are designed for high reliability. Multiple destinations and the take button feature allow a single panel to be used for multiple devices connected to the router, and dramatically lowers the cost in large facilities.ĭesigned to be easy for customers to self install Videohub Smart Control Pro uses standard ethernet networking and simply plugs into the existing computer network. Videohub Smart Control Pro also allows the use of a "take" button, and when enabled, the take button is the lower right button, and illuminated red. When working with multiple destinations, buttons on the front panel become gold colored and customers can select as many destinations as they need. Videohub Smart Control Pro can also be used with multiple destinations, and customers can select to have a single destination for the whole control panel, or multiple destinations. Videohub Smart Control Pro includes a USB connection and easy to use Mac and Windows software to set each button. This is a much faster way of working, because all routing only requires a single button press. Videohub Smart Control Pro can be installed under each deck and monitor in a facility, so the router output to that monitor can be set with a single button press. If you believe this is a problem consult your local IT administrator.Blackmagic Design's Videohub Smart Control Pro is a multi button control panel for XY or single destination control that also supports ethernet. El Videohub Smart Control Pro es un panel compacto de 1U que permite controlar la matriz mediante una red Ethernet. The second potential problem is a common one when using RouteMaster: Any firewall software or systems must be configured to allow the RouteMaster PC to receive incoming connections on port 9990. If these services are installed, please make sure these Windows services are both stopped and disabled. The usual culprits for this are the Windows Services for “Blackmagic Videohub Daemon” and “NVidia Network Service”. On older software you’ll see this error in RouteMaster on clicking the “Run” button If this happens, you’ll see the Videohub client shown in red when Menu/Settings/View Client Info is selected. The first is that RouteMaster cannot use port 9990 because another application is already doing so. There are two common problems that you may encounter. Elgato Streamdeck (with Bitfocus Companion).Many other control panels and interfaces use Videohub protocol to control routers, and can be used successfully with RouteMaster. These are sent to RouteMaster as a sequence of individual commands. Each salvo can make up to 16 routes at once. You can use the regular Videohub ‘Macro’ capability to define salvos directly in the panel. Programming the panel for source and destination selection is performed using Blackmagic’s utility in the same way as for a regular Videohub router. If successful, you’ll also see the panel IP shown in the Routemaster main screen. If Routemaster is running and configured, you’ll get a green light shown. ![]() We need to enter the IP address of the Routemaster system PC as the “Remote Videohub IP”. Start the BlackMagic Videohub Control Utility, and locate the panel you wish to configure. ![]() ![]() Next, we need to configure the panel to communicate with RouteMaster. Make sure your router is correctly configured and connected to RouteMaster, and can be controlled from the RouteMaster main screen. Here’s how to set them up.Įnable Videohub emulation in the Client configuration dialog. Blackmagic Design’s Videohub Smart Control and Videohub Master Control hardware panels (and their newer ‘Pro’ versions) can be used to control any router connected to RouteMaster, regardless of make.
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |